Do It Yourself Bath Setup.
Do It Yourself Bath Setup.
Blog Article
Presented here down the page you will discover a good deal of very good resources around How to Install a Bathtub.
Setting up a bathtub isn't specifically rocket science, yet it does require strong plumbing, woodworking, as well as often, tiling skills. Replacing an old bathtub with a new one is also a reasonably challenging job. If the old tub is conveniently available, the task can relocate quickly; if you need to open a wall to get rid of the old tub and also position the new bath tub, the task is a lot harder. In either situation, the project is within a residence handyman's skills, although you will certainly need a helper to leave the old tub and also set in the brand-new one. Make certain you have actually qualified on your own for the task and fit attempting it. As opposed to hiring a service provider to take over a halfway-completed task, it is better to take into consideration employing one prior to you start. Possibilities are you might need a professional plumber to make tube links.
This article will certainly help you set up a brand-new tub in your washroom if you have currently bought a brand-new bathtub as well as do not need to transform the arrangement of your previous water system pipes.
Your tools and also material list should make up the following:
Planning for the Installment
Firstly, the supporting framework provided with the bathroom should be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the taps device to prevent strain on the tub.
Fit the adaptable faucet connectors to the bottom of the two faucets making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom must currently prepare to be suited its last position.
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is detach the water system. After doing so, activate the faucets to drain pipes any water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly bothersome as a result of the limited gain access to that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the faucets. Have a fabric prepared for the staying water that will certainly originate from the pipelines. When the supply pipelines have actually been eliminated, utilize the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from turning during this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any old sealing substance.
Prior to carrying on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Mounting the Tub
Using both wood boards under its feet, put the bath tub in the called for placement. The wood boards are practical in uniformly spreading the weight of the bath tub over the area of the boards rather than focusing all the weight onto four tiny factors.
The next objective is to make sure that the tub is leveled all round. This can be achieved by checking the level as well as adjusting the feet on the bathtub till the level reads level.
To mount taps, fit all-time low of the furthest adaptable faucet connector to the ideal supply pipe by making a compression sign up with; after that do the same for the various other tap.
Activate the supply of water and also inspect all joints and also new pipework for leakages as well as tighten them if necessary. Load the bathtub as well as also examine the overflow outlet and also the typical electrical outlet for leaks.
Ultimately, repair the bathroom paneling as explained in the supplier's instruction manual. Tiling and also sealing around the bath tub should wait till the bathtub has actually been used at least once as this will certainly settle it right into its final placement.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will need lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the installing hole in the bath/basin guaranteeing that the washing machines are in location in between the tap and also the sink. Secure the faucet in position with the producer given backnut. Once the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical faucet ports. The previous type needs to be connected to the faucet finishes first, tightening up only by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the location where the bath satisfies the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to split a stiff seal, causing the water to penetrate the wall in between the bathroom as well as the tiling, resulting in complications with wetness and feasible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your components and also fittings. They are offered in tubes and cartridges, as well as can sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill the bathtub with water before sealing, to enable the motion experienced when the bathtub remains in usage. The sealer can crack fairly early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water resistant glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our section about Tools You Need to Install a New Bathtub . Thanks so much for taking a few minutes to read our blog. Don't hesitate to set aside a second to promote this entry if you appreciated it. We appreciate reading our article about How to Install a Bathtub.
Request A Quote Report this page